Kit consists of 500g of PART A and 500g of PART B
Total kit volume 920ml
This product is odourless, non-toxic and formulated specifically for applying to the human body.
PART A is a red liquid and PART B is a blue liquid which act as a visual aid, turning purple during the mixing process. The two components mix easily with a simple 1:1 ratio with a working time of 5-8 minutes with a cure time of 20-30 minutes @ 25°C.
Once cured the rubber is a flexible, elastic, material with outstanding release properties, a high chemical resistance and a temperature resistance of 200°C. There is practically no shrinkage (0.1%) and excellent reproduction of fine detail.
As the moulds will be thin to hold their shape when filling with the casting material an outer support will need creating whist the rubber is still in situ on the body. We recommend mod roc plaster bandages.
One Hand and Wrist
500g of Thixo Body Moulding Rubber
3 x (15cm x 2.7m) Modroc Bandages
One Arm with Shoulder
2kg of Thixo Body Moulding Rubber
8 x (15cm x 2.7m) Modroc Bandages
Face
500g of Thixo Body Moulding Rubber
3 x (15cm x 2.7m) Modroc Bandages
Face and Partial Neck
1kg of Thixo Body Moulding Rubber
4 x (15cm x 2.7m) Modroc Bandages
Front Half of Head
1kg of Thixo Body Moulding Rubber
5 x (15cm x 2.7m) Modroc Bandages
Full Head and Neck
2kg of Thixo Body Moulding Rubber
10 x (15cm x 2.7m) Modroc Bandages
Chest
2kg of Thixo Body Moulding Rubber
8 x (15cm x 2.7m) Modroc Bandages
Full Torso Front and Back
7kg of Thixo Body Moulding Rubber
34 x (15cm x 2.7m) Modroc Bandages
One Foot
1kg of Thixo Body Moulding Rubber
4 x (15cm x 2.7m) Modroc Bandages
One Lower Leg
2kg of Thixo Body Moulding Rubber
10 x (15cm x 2.7m) Modroc Bandages
One Full Leg
5kg of Thixo Body Moulding Rubber
18 x (15cm x 2.7m) Modroc Bandages
| Properties | Units | Thixo Body |
| Pot Life (25°C) | Minutes | 5-8 |
| Cure Time (25°C) | Minutes | 20-30 |
| Viscosity (25°C) | Mpa.s | 5500 |
| Density (25°C) | g/cm3 | 1.08 |
| Hardness | Shore A | 20 |
| Linear Shrinkage | % | 0.1 |
| Tear Strength | KN/m | 26 |
| Elongation at Break | % | 500 |
| Tensile Strength | Mpa | 6 |
Technical Data Sheet Safety Data Sheet Part A Safety Data Sheet Part B
THE FINISHED MOULD IS SUITABLE FOR USE WITH:
Polyurethane resin
Epoxy resin *
(* Excl. some epoxies, check with supplier of the resin if silicone moulds are suitable.)
Polyester resin
Acrylic resin
Plastisol (PVC)
Plaster
Cement
Polymer clays (Will inhibit the cure of liquid platinum silicone, see below)
Waxes
Soaps
Metals with a pouring temperature below 250°C
*CURE INHIBITION*
A release agent will not create a sufficient barrier to prevent cure inhibition but a layer of paint will. If the paint is solvent based allow sufficient time for the solvent to completely evaporate off as that too can inhibit the cure
Great care must be taken when handling and mixing all addition-cured silicone elastomer systems. All the mixing tools (vessels and spatulas) should be clean and constructed in materials which do not interfere with the curing mechanism. The cure of the rubber can be inhibited by the presence of compounds of nitrogen, sulphur, phosphorus and arsenic; organotin catalysts and PVC stabilisers; epoxy resin catalysts and even contact with materials containing these substances e.g. moulding clays, sulphur vulcanised rubbers, condensation cure silicone rubbers, some printed plastics, onion and garlic.
